Adopt Machine Safety standards now, says Pilz
February 21, 2011 - As the Machinery Directive EN 13949-1 standards better reflect state of the art in Machine Safety System design, machine builders should adopt these standards sooner rather than later, says Kevin Ives, Machinery Safety Consultant at Pilz Automation Technology.
The latest version of the Machinery Directive has now been with us for some time. 2006/42/EC was introduced in 2006 and published in the “Official Journal” (OJ) in September 2009. The publishing of any article, directive or notification of a standard in the OJ is the point at which the use of the document becomes mandatory.
Ever since the first Machinery Directive, the recommended method of meeting all of the Essential Health and Safety Requirements (EHSR’s) was to follow the advice in the “Harmonised Standards.” These are standards that have been written in support of the directive. A list of the standards applicable for use against the directive is printed in the OJ following the ratification of the directive.
As with the directives, the standards are being improved/upgraded with new versions being announced in the OJ as being harmonised against the relevant directive. In 2007, the long awaited replacement for Safety of Machinery – Design of safety related control systems EN 954-1 was printed. This standard, EN 13949-1, has the same title and seeks to achieve the same ends but uses a risk-based approach. The standard introduces new criteria such as Diagnostic Coverage (DC) and Mean Time To Dangerous Failure (MTTFd), which need to be taken into consideration when designing the system.
The normal situation, when a standard is rewritten, is to allow a two-year “change over” period. This is provided to enable manufacturers to modify their design and documentation to align with the new requirements. Using this rule, EN 954-1 should have been revoked and replaced by EN 13849-1 in late 2009. The inclusion of EN 13849-1 as a harmonised standard against 2006/42/EC was announced in the OJ in September 2009.
At this point, the problems started to emerge. There were a few complaints made to the commission claiming that two years did not allow sufficient time for some manufacturers of components to provide the information and data needed to calculate failure rates, as required by the latest standard. The commission agreed and therefore delayed revoking EN954-1 until the end of 2011. The latest list of harmonised standards that can be used to demonstrate compliance with the directive, does not list EN 954-1. This list was printed in the OJ dated 20th October, 2010. This clouds the issue further. In theory, manufacturers cannot use standards that are not harmonised to claim compliance with the directive, but EN954-1 will not be revoked until the end of 2011.
All of the machine-specific standards (C standards) that were written before the introduction of EN 13849-1 list EN 954-1 as an appropriate standard to use for the design of the safety-related controls. This raises even more confusion.
As the newer standards better reflect state of the art in Machine Safety System design, Pilz therefore recommends that machine builders adopt these standards sooner rather than wait until the end of the transition period. Why? Because we believe the future of automation and machinery lies in flexible, modular architectures, which will provide users with the high level of availability and adaptability required for agile, lean manufacturing plants. Modern plant and machinery will therefore require intelligent safety systems.
The new standard reflects this increased tendency to use electronic and programmable systems for safety rather than traditional electromechanical devices that were used when EN 954 was published. EN 13849-1 provides requirements for the design and integration of safety-related parts of control systems, including software. It has wide applicability as it applies to all technologies, including electrical, hydraulic, pneumatic and mechanical.
While acknowledging the decision of the EU, we believe that the probabilistic approach of the new standards provides machinery designers and users with many advantages when assessing the reliability of safety systems. While there is an increased complexity in requirements to make design calculations, tools such as Pilz’s PAScal Safety Calculator are available to calculate the required Performance Level (PL) and Safety Integrity Level (SIL). This software also evaluates a safety system designs and then generates the necessary documents to be included in the machine’s technical file. Training courses are also available on the new Machinery Directive 2006/42/EC, including one, two and four-day City & Guilds Machinery Safety Courses, Safety Design and CE Marking.
Furthermore, those companies designing and manufacturing new machinery who apply one of the new standards now, will not incur additional costs of design, validation, and documentation when the transition period ends in December 2011.
Pilz Automation Technology develops, manufactures and supplies process and automation control products for use wherever there is a requirement to ensure the safety of plant, personnel or the environment. Included in the range are: safety relays; configurable safety controllers; programmable safety systems (safety PLCs) for use with or without the SafetyBUS p safe, open industrial fieldbus network; mechanically actuated and non-contact guard switches; safety light curtains; 2D and 3D vision-based safety sensors; emergency stop switches; conventional and touchscreen operator interfaces; plus control and monitoring relays for non-safety applications.
MORE INDUSTRY NEWS
International Federation of Robotics: Reject Bill Gates' idea to tax robots
The IFR strongly supports the idea of greater cooperation in robotics between the public and private sectors. They must adapt education and...
ISA announces IACS Security Lifecycle Training Program w/ Cyber Trainers
The Cyber Trainers are designed and equipped with full-function industrial automation system hardware and software configured to perform like the...
Schneider Electric partners with ENGIE to digitize energy sector
The two will explore and deploy new digital solutions for operational efficiency of renewable assets (wind and solar PV), leveraging Supervisory...
Aegis Software and ViTrox announce mutual machine programming interface
The machine programming interface between ViTrox Corporation’s automated X-Ray-inspection (AXI) machines and Aegis’ FactoryLogix software will...
Phoenix Contact announces winner of Nanoline Contest to kick off National Engineers Week
Forty-nine teams registered for this year’s competition at the regional level, and eight teams from Pennsylvania, North Carolina, and Indiana...
Safety Instrumentation Simplified: The case for a hybrid safety transmitter
By Wil Chin and Rick Frauton, United Electric Controls
While there remains considerable variation in the quality of the sub-system infrastructure,...
The New Era of Automation Architectures: What does it mean for users?
By Bill Lydon, Editor, Automation.com
The application of revolutionary new concepts and technologies, including the Internet of Things (IoT),...
Cloud-Based MES: The Effort to Empower Small Manufacturers
By Bill Lydon, Editor, Automation.com
In this day and age, it can sometimes seem like the small manufacturer is getting buried underneath the...
HARTING to introduce integrated connectivity solutions at Hannover Messe
HARTING ix Industrial, HARTING T1 Industrial and M8 D-coded are three of these miniaturised connectivity solutions for the industry of the future.
Microscan announces updates to their free barcode generator
The barcode generator is a free online tool enabling users to create, save, and email custom barcodes. 28 different barcode types, from linear to...