- October 13, 2011
- Case Study
OMS engineers internally inspected Serimax welds on subsea pipes that were destined for use on BP‚Äôs Devenick high pressure, high temperature gas project.
October 13, 2011 - Oil and gas pipe measurement specialist Optical Metrology Services (OMS) completed a series of pipe measurement surveys for French company Technip. In the last few months, OMS has completed several pipe measurement surveys for Technip. The first of these was carried out at Technip’s Evanton Spool base in Scotland in August 2011. OMS engineers internally inspected Serimax welds on subsea pipes that were destined for use on BP’s Devenick high pressure, high temperature gas project. OMS engineers spent five days on site inspecting the welds immediately after the second pass, using its own unique combination of video and laser-based measurement tools. As Jim Buston, Client Solutions Executive at OMS states, “This powerful combination of tools enabled our fully qualified weld inspectors to verify, unquestionably, whether the welds met the HiLo requirements of the project and if any weld features were within allowable tolerances. Used in conjunction with OMS’ pipe fit-up optimisation software [SmartFit], this creates a very powerful toolbox for customers such as Technip, resulting in better, faster welds and fewer cut-outs.” Following this successful survey, OMS was invited by Technip’s OED research and development division to carry out a pipe measurement survey (also at Evanton) of pipe end geometry and the implications of this on pipe fit-up. The survey involved OMS inspecting a small sample of 8-inch and 10-inch pipes and then analysing the resulting measurement data. The pipes were fatigue string joints with a 3mm thick nickel alloy overlay. The pipes were internally counterbored. The objective of OMS’ survey was to provide Technip with the best fit-up in terms of pipe end-to-end matching, reducing the centre eccentricity, out-of-roundness match and local Hi-Lo. OMS inspected the pipe ends using its Laser End Dimensioning Tool and SmartFit fit-up optimisation and sequencing software. Technip’s aim was to achieve a maximum external Hi-Lo of 1.2mm on the project. The measurement results showed that this figure could be reduced to 0.4mm using SmartFit. “Laser measuring of pipe ends is nothing new. Many pipe mills supply laser-gathered data with the pipes they produce. However, our SmartFit software takes this further by utilising 2,000 data points linked circumferentially to create a measurement profile. This is then used to simulate two pipe ends meeting for a joint – producing the details of HiLo misalignment as well as the best fit rotation,” explains Jim Buston. OMS has recently been invited to carry out a further similar pipe measurement survey at Technip’s Evanton spool base on a small sample of fatigue-sensitive pipes. On this survey, OMS will inspect six, 10-inch pipes (12 pipe ends) that have a 50mm long, machined clad overlay. OMS will provide best fit-up in terms of pipe end-to-end matching using its Laser End Dimensioning tool and SmartFit software. The project will take place in October 2011. Pipe reeling trials at Heriot Watt University Technip also requested OMS to inspect mechanically lined pipes for reeling. To demonstrate this, two 10-inch pipes were manufactured and bending trials carried out at the Heriot Watt University in Edinburgh on 21st September 2011. On the day, in order to demonstrate the robustness of the pipe design, OMS provided internal video inspection pre- and post-bending in order to verify and monitor the results. “The high resolution video inspection system with super bright variable, multi-axis lighting enabled our engineers to look for any unwanted wrinkles in the liner of the pipe, particularly before and after the bend. We were also able to record and provide still images and video footage to Technip as and when required. The reeling tests were successful and were witnessed by some of the world’s leading oil producers,” adds Jim Buston. About Optical Metrology Services Optical Metrology Services Limited (OMS) is a market leader in the provision of pipe measuring products and services. The company specialises in measuring equipment and consulting services for use within the pipe manufacturing and pipeline construction sectors, both onshore and offshore. A key focus for OMS is in the dimensional measurement of oil and gas pipes or other structures such as military gun barrels, processing industry tubes or manufactured cylindrical objects, where dimensions are critical. OMS prides itself on finding out what clients require and delivering it. OMS was recently recognised by being awarded The Queen’s Award for Enterprise in the Innovation Category, the company’s second award in 2007 (the first award being the Pipeline Industries Guild Award for Land Based Technology). The OMS Pipe Checker range of tools provides dimensional checks on all aspects of manufactured pipe. These tools are used throughout the world for onshore and offshore projects and in pipe mills.Learn More
Did you enjoy this great article?
Check out our free e-newsletters to read more great articles..Subscribe