The Brooks Instrument MT3809 metal tube VA flow meter is designed for extreme conditions in chemicals, petrochemicals, oil and gas, and LP gas applications.

The Picomag combines a sensor and transmitter in the same housing, with a 1.4-inch TFT color display showing flow, totalizer and temperature readings, as well as warning and alarm messages.

The FT4X was designed to be used in Oil & Gas and Industrial applications. It is suitable for applications monitoring pure gases, mixed gases, and even complex flare gas compositions.

Heartbeat Diagnostics’ continuous analysis of transmitter/sensor system health status during operation enables recognition of related events when they occur.

The Tolomatic ServoChoke SVC electric choke valve actuator is designed to meet requirements for a more flexible high-speed actuator in performance drilling applications such as managed pressure drilling (MPD), set-point control or choke-and-kill.

EtherCAT joins Alicat’s offering of industrial automation protocol options, which also includes Modbus TCP/IP, Modbus-RTU, EtherNet/IP, DeviceNet and PROFIBUS communication options to fit new or existing systems.

The flow system is designed for multiple industries requiring budget-conscious liquid flow instrumentation, including water and wastewater, power, HVAC and chemical.

Process engineers responsible for on-site plant biomass combined heat and power (CHP) systems may find the ST51 Series Thermal Mass Flow Meter from Fluid Components International (FCI) provides accurate measurement of syngas fuel flow to the CHP engine.

The Sinamics V20 I/O extension module is mounted on the converter using Plug & Play technology, and provides two additional input and output interfaces, each for 400 volts., designed to increase both the flexibility and the scope of the Sinamics V20.

The MPFM 2600 is part of the scalable Roxar Multiphase Meter product family built on measurement principles used in over 1,500 meter installations worldwide, and enables shale operators to monitor the flow from the well stream continuously and in real-time.

Working together, the Flow Meter and Totalizer can measure, locally display and wirelessly transmit intelligent flow data to a Gateway for remote monitoring and control on a PC, PLC or other control system.

The FS10i Flow Switch/Monitor operates over a flow range in air/gas from .25 FPS to 400 SFPS [0,076 MPS to 122 MPS] and in water from 0.01 FPS to 0.5 FPS [0,003 MPS to 0,15 MPS]. Repeatability: ±0.5% of reading.

These valves are designed to Class 800 and provide tight shutoff, suitable for steam, condensate and other liquid systems. They are available in NPT and SW versions, in sizes from ½” to 2”, in either forged carbon steel or forged stainless steel.

FCI’s inline FLT93L Flow Switch is a thermal dispersion flow/level/temperature switch that was designed based on FCI’s more than 50 years of flow/level/temperature switch applications experience

Nordson ASYMTEK's 2-in-1 dispensing system and inspection kit provides process control for consistently jetting small volumes as low as 1 nanoliter at frequencies up to 1000 Hz.

Typical uses of the WM-NLCH flow meter include residential and commercial metering and sub-metering applications that use hot water: industrial food, beverage & plant process water usage, industrial laundry, industrial baking, cement mixing, apartment/condo complexes.

The family of modular S80-T80 Liquid Analyzers from Electro-Chemical Devices (ECD) is designed to provide engineers and managers with the process data they need to obtain and maintain a wide range of global, regional and local quality, environmental, safety and other certifications.

The expanded G3 and 580 Series platforms feature process control architecture that permits the design engineer or end-use specifier to optimize the size of the control cabinet for the number of required valves.

Designed specifically for flow measurement in round pipes or stacks of 12 inches [300 mm] and larger diameter, and square or rectangular ducts with cross sectional area of 100 inches [250mm] and larger, the model ST102A Flow Meter and the new MT100 Series Flow Meters from Fluid Components International (FCI) provide two to eight non-clogging, no moving parts sensing points.

The IP68 fiber plugs and IP68 fiber receptacles offer 400lb pull strength and 450lb crush resistance as well as protection from moisture, liquid and dust.