Retractile cordsets for PROFIBUS-DP networks may be extended up to four times their original retracted length. This makes the cordsets ideal for motion and robotics in automotive applications.

SlotServer ControlLogix/Metasys N2 Interface Module enables a user to interface third party devices utilizing Metasys N2 to the ControlLogix 1756 platform. Metasys N2 is a protocol developed by Johnson Controls and widely used in the building automation industry for energy monitors, HVAC controls, I/O controls, lighting controls, motor controls, and sensors.

The kit contains four CS Series capacitive sensors, one DS-2100 WiFi display and summing device with wireless connection capability, LoadVUE software for simplifying measurement and calibration tasks using a PC, all the data cables and a 9V power adapter to connect and power the system. It can connect wirelessly to a PC using 802.11b WiFi interface.

ProtoCessors daughter cards that enable OEMs to interface legacy devices to modern open protocol networks without extensive board redesign. Protocols available include Allen Bradley EtherNet/IP, BACnet IP, BACnet MSTP, Modbus RTU, Modbus TCP, Metasys N2, DNP3, LonWorks and a wide variety of legacy and proprietary protocols.

CU2008 and CU2016 Ethernet switches have a stainless steel/aluminum housing via an integrated DIN rail adapter. The switches relay incoming Ethernet frames to the destination ports. In full duplex mode, they prevent collisions. They can be used universally in automation and office networks.

WLS-TC and WLS-TEMP temperature data acquisiton systems have an RF module, which allows for wireless data transfer. Users can acquire and process temperature data for monitoring and control at distances up to 150 feet indoors, and as much as 2460 feet line-of-sight outdoors.

OS24-SR Solar Power Supply provide power to a Wireless Radio Modem to function as an Access Point and/or Repeater. It uses a high efficiency photovoltaic solar module (PV) to convert the sun’s energy to 12 Volts dc. The system's solid-state controller maintains continuous battery monitoring and temperature compensated charging during daylight hours.

KAN354B router provides a BACnet WiFi Mesh network for indoor commercial and industrial building systems. It enables new and retrofitted buildings to be outfitted with state-of-the-art building controls with minimal or no new wiring required. BACnet is a standard protocol for building automation and control systems.

SCANEX barcode readers have Gas Zone 1 and Dust Zone 22 ATEX approvals, with North American approvals pending. The readers are available in hand-held versions with wireless or cabled operation, stationary miniature styles, and intrinsically safe models. SCANEX may be used for production management in a variety of industries with hazardous locations.

Intermec's CN3 and CV30 wireless mobile computers will use AirForce One Wi-Fi technology from Broadcom. The addition of Wi-Fi technology optimizes device security, roaming and interoperability and offers higher levels of integration, power savings and voice over IP performance.

AVIAOK, Drivven and S.E.A. have developed custom wireless modules for the CompactRIO platform. Modules are suitable for automotive, aerospace and military in-vehicle applications; wireless communications; position monitoring for mobile applications; and direct connectivity to in-vehicle sensors for electronic control unit (ECU) design and rapid prototyping.

The Memor pocket-sized Windows-powered mobile computer is an extremely compact, lightweight, versatile and robust device that combines integrated bar code reading and wireless communication capabilities. It is suitable for light industrial operations such as warehouse management, inventory, picking, shipping, receiving, etc.

The Wireless Logic Controller platform simplifies the integration and development of automation systems and enterprise control solutions with hardware, user programmable IEC 61131-3 standards-based middleware, and end-user data communications. Development, monitoring and control is made easier through the use of integrated cellular communications, industrial hardened I/O, and standard fixed-wire networks integrated into one rugged design.

These sensors are designed to measure rotating drive torque using a conventional shaft-to-shaft configuration for in-line placement. The design incorporates a digital non-contact wireless system that provides power to the rotating electronics mounted on the shaft and transmits the signal back to the receiver in digital format.

Zlinx wireless remote I/O maps directly into a Modbus table, making it an easy fit to any PLC, HMI or PC based control system running LabVIEW or other popular automation software. Wireless modules provide Modbus compatible communication at ranges up to 20 miles.

GS110 Process Imaging System for Low Emissivity (Low-E) glass monitors one-side coated flat glass. With the addition of an IR point sensor to measure the temperature on the uncoated side of the glass where the emissivity is both known and significantly higher, the GS110 can automatically correct the thermal image and provide a more accurate result.

InRAx Wireless Ethernet/IP Communication Module (MVI56-WA-EIP) acts as a wireless bridge, enabling remote connectivity between a ControlLogix processor and 802.11 wireless devices including PCs, Laptops, radio modems, and other modules. It allows programming over the backplane and acts as a server to RSLinx, allowing for multiple programs such as RSLogix5000 and/or RSView products to communicate simultaneously with the processor.

Two new EtherNet/IP module options for the Allen-Bradley ControlLogix include USB ports, easy setup and replacement. The modules work with existing EtherNet/IP products and provide capacity to allow for future expansion of user networks. They use the Intel IXP465 network processor chip designed specifically for the rigorous performance demands of manufacturing environments.

The PROFINET IO development kit enables simple implementation of PROFINET I/O devices according to the PROFINET standard and supports real-time (RT) operation.

The Industrial Ethernet Module enables fast, low-cost connection of devices to ETHERNET Powerlink, EtherNet/IP and PROFINET. The module is based on an Altera-FPGA and contains the CPU (NIOS II), an Ethernet Controller and an integrated 2-port hub, which is routed out via an RJ45 connector. Depending on the version, the protocol software for implementation of an ETHERNET Powerlink controlled node, a PROFINET device or an EtherNet/IP adapters is already on the module.