-
ISA provides technical resources and standards to help industrial automation professionals advance their careers and the field. We enable automation professionals worldwide to solve problems and enhance their skills by bringing people together to create new technologies and share best practices with future automation professionals.-
ISA Resources
-
Upcoming Events
-
Industry Insights
-
Consortia
-
Automation Quiz
Test your knowledge of the automation industry with questions from ISA certification programs.
249 Results Found
-
FeatureAutoQuiz: What Is the Purpose of a Valve Positioner?
A valve positioner adjusts the pneumatic output to a valve actuator so that the requested position of the valve from a controller is achieved. -
Feature
AutoQuiz: Models of Control to Describe a Batch Process
A process stage in the process model can be mapped to a unit procedure in the procedural model, which in turn is mapped to a unit in the physical model. -
Feature
AutoQuiz: Which Type of Electrical Wires Would Normally Be Shielded in Control Systems?
Cable shield, connected to an isolated zero potential, is required to prevent nearby inductive loads and EMF fields from altering the low-level voltage or current levels in the signal wiring. -
Feature
AutoQuiz: What is Common Mode Noise?
Common noise must be in phase between conductors, or it converts to normal mode or differential noise. -
FeatureAutoQuiz: What Are the Advantages of Cascade Control?
Cascade control does very little to improve upon control loops that were previously stable. Examples are liquid level and gas pressure control loops. -
FeatureAutoQuiz: Characteristics of a Flowmeter
For a turbine flowmeter, the rotor is supported by the hubs and bearings inside of a flowmeter body, and as the rotor spins, the number of revolutions is determined with a magnetic pickup. -
FeatureAutoQuiz: How to Measure the Temperature Between Two Dissimilar, Joined Metals
A thermocouple contains two different conductors that produce a voltage proportional to a temperature difference between the ends of a pair of conductors. -
FeatureAutoQuiz: How to Measure Fluid Velocity Through a Pipe
The constant between pipes of differing diameters is the flow rate (and other fluid properties) is the same in both pipe lengths. -
FeatureAutoQuiz: Design Specifications for Building Automation Systems
Energy management, access control, lighting control, asset management, communications, life safety, fire alarm, and HVAC controls are all of interest when designing a building automation system -
Feature
AutoQuiz: What Is the Continuous Sequence of Steps Performed by a PLC Processor?
The time it takes for the PLC to complete its scanning of all program steps in one operating cycle is called the scan time. -
FeatureAutoQuiz: What Network Security Technology Does Not Use Encryption?
A virtual local area network (VLAN) is achieved through configuration of Ethernet switches and not encryption. It divides a physical network into smaller logical networks to increase performance, impr -
Feature
AutoQuiz: What Is the Purpose of the Proper Grounding of Electrical Devices?
Proper grounding provides safety, over-current protection, electrical noise reduction, lightning protection, and static electricity reduction. -
Feature
AutoQuiz: How to Calculate the Pressure Recovery Factor for Valves
Pressure recovery factor is the increase in fluid static pressure that occurs as fluid moves through a valve from the vena contracta to the valve's outlet and downstream piping. -
FeatureAutoQuiz: What Are the Four Key Activities in the Maintenance Cycle of a Control System?
Documentation of the "as left" condition of the control system is a basic requirement for all maintenance, calibration, commissioning, and testing tasks. -
Feature
AutoQuiz: What Are Multiple Independent Protection Layers in Relation to Industrial Safety?
A consequence of the concept of multiple independent protection suggests minimization of risk occurs when safety instrumented systems are completely independent from process control systems. -
FeatureAutoQuiz: What Is the Response in Level Control System If the Process Liquid Medium Changes?
For a capacitance probe installed in a metal tank, the measured level is proportional to the measured capacitance between the level probe (one capacitor plate) and the tank wall (second capacitor plat -
FeatureAutoQuiz: How to Determine Cause of the Apparent Discrepancy in Flow
Periodic visual inspection of orifice plates is required to ensure the integrity of measurement with a digital flow transmitter. -
FeatureAutoQuiz: Which Flowmeter Type Does Not Operate on the Principle That a Differential Pressure Is Developed Across a Flow Restriction?
A Coriolis flowmeter develops a flow measurement by measuring the degree of deformation (twisting) of a vibrating tube(s) as the fluid moves through the tube. -
FeatureAutoQuiz: What Is an Example of Adaptive Control?
A controller uses a quantitative process model and modifies controller tuning based on how the process responds in relation to the model prediction. -
FeatureAutoQuiz: P&ID Determination for Temperature and Pressure Sensors
Instrument technicians often use P&ID diagrams as a reference to identify what type of instrumentation is installed and how the instrumentation is installed in the process.
